Textile Waste

1. Home
2. Products
3. Textiles & Leather Products
4. Textile Waste

Share us

2690KGS Water Jet Weaving Loom Machine High Density Dobby Shedding

SD8100

Send Inquiry

Description

Must-Purchase-Brand DRDE New Generation SD8100 Series Water Jet Loom Machine Open To Order

DESCRIPTION

?

Things That You Should Know About This Beauty....

- - - -
Model | SD8100 |
Loom Width | 190cm / 75 inch |
Reed Width / Actual Weave Width | 40 ~ 70 inch 110 ~ 180cm |
Speed | ?530 ~ 580 RPM |
Weft Picks | 13 ~ 140 PICKS / INCH |
Take-up / Let-off | ELECTRIC |
- - - -

APPLICATION

You Can Freely Use Following Yarns (Included But Not Limited) On Our Water Jet Loom According To Your Requirement .

- - - -
1 | Fdy |
2 | Dty |
3 | Aty |
4 | Roto |
5 | Cationic |
6 | Spun |
7 | Spandex |
8 | Micro |
9 | High Stretch Yarn |
10 | Nylon |
11 | Viscose |
12 | Metal Filament |
13 | Mono-Filament |
- - - -

And Following Polyester Fabric (Included But Not Limited) Will Be?Easily Woven By Our Water Jet?Loom Machine .

- - - -
1 | Polyester Satin |
2 | Chiffon Polyester Fabric |
3 | Taffeta |
4 | Taslon Fabric |
5 | Pongee Fabric |
6 | Spandex Fabric |
7 | Crepe |
8 | N/P Taffeta |
9 | Saree Fabric |
10 | Peach Skin |
11 | Micro Peach |
- - - -

?

THE MAIN ADVANTAGES OF DRDE WATER JET LOOM MACHINE

?Which You Should Buy And Have For Best Benefit......



1. Designed with offset solid locking shaft as per Tsudakoma ZW8100 , Suitable To Weave Fine Yarn At High Picks



2. Single-pieced Frames Are Used?Instead Of two Pieces Joined, Thus Gained More Stability When For High Speed Weaving .?



3.?Electric Blower Is Applied.

Mostly Mechanical Blower Is Used To Suck And Dry The Fabric ; But There Are Two Situations Where Electric Blower Is Required.

3.1 One Is When The Loom Is Running In High Speed (Above 600rpm) ,

3.2 And The Other Is The Fabric Is High Gsm ; Under These Two Situations , The Fabric Is Unable To Get 80% Dry , Therefore , It’S Better To Use Electric Blower Which Has Better Dry Effect .



4.?Electric Let-Off System .

Traditionally, With Water Jet Loom Machine?, The Feeding Of Warp Yarn Is Controlled By Mechanical Let-Off System . For Some Quality , The Usual Mechanical System Is Unable To Detect The Subtle Tension Variation , Thus Sometimes Stop Mark Will Happen To The Fabric . While With Electric Let-Off System By Cpu Control , Even Very Subtle Tension Fluctuation Will Be Detested And Rectified Accordingly To Prevent Stop Mark .



5.?In This Picture , You Are Seeing The Bottom Support Of Drde Water Jet Loom Machine?. Not Like Other Suppliers Who Are Using A “L-Shaped” Bar Support ; We Are Actually Using Triangle Pipe Type Support . This Type Of Support Has Better Anti-Rust Effect And Less Viration . And For Water Jet Weaving Machines , Less Vibration Means Less Break-Down And Better Grade Fabric Output.



And This Is The Design Of Other Suppliers ....



6.?This Is Bobbin System, Which Plays Important Role For Feeding Warp Yarns. Our Bobbin System Is Properly Balanced And Hard-Worn And Very Sensitive To Warp Tension Variation .



Talk To Robert To Know More ...

?

Read More