Electronics Designing & Processing
Description
HDMI Signal Extender all to HDMI with HDBaset 100m Cat6 Extender
?
Introduction :
The cat5e / cat6 HDMI Extender is a tool which can extend your HDMI signal over 230fts / 70meters to a compatible display . It is designed to convert HDMI signal to standard HD BaseT signal which can be transmitted by LAN cable . It also supports Transfer Bidirectional Infrared control signal together with the HDMI signal , so you can control the Source in the Sink side which is 230fts outside , also you can control the Sink in the Source side which is 230fts outside by using the HDMI Extender .
?
Features :
?
?1 . POE ( Power Over Ethernet ) function is supported , either TX or RX is powered by24V @ 1A power supply , the another does not need power supply from the DC jack . POE Power consumption is less than 10W . ※ See the description 1
?2 . Use single UTP LAN cable ( CAT - 5E / 6 ) to substitute HDMI cable to achieve long distance transmission .
3 . UTP termination follows the standard of TIA / EIA - 568 - B .
?
4 . Transmission distance :
4.1 :?Over CAT6 cable
4.2 : 70 meters : 1080P @ 60Hz36bit ; 3D1080P @ 30Hz36bit ;
4.3 : 40 meters : 1080P @?60Hz @ 48bit; 1080P @ 120Hz@24bit ;?3D1080P @ 60Hz @ 36bit ; 4K x 2K @ 30Hz @ 24bit .
?
5 . Support display resolutions up to 4K x 2K @ 30Hz?
6 . Full HD support :?1080p @ 60Hz @ 48 bit / pixels , 1080p @ 120Hz @ 24 bit / pixels ,?3D 1080P60Hz and 4K x 2K @ 30Hz @ 24bit .
7 . Transfer Bidirectional Infrared control signal together with the HDMI signal .?※ See the description 2 .
8 . Transfer Bidirectional RS232 control signal together with the HDMI signal .?※ See the description 3 .
?
?Specifications :
?
- - - -
# Frequency Bandwidth | # 297MHz [ 10 . 2Gbps ] |
# Transmitter Input / Output Ports | # 1 x HDMI Female port / 1 x CAT6 |
# 1 x IR Tx / 1 x ?IR Rx / 1 x Phoenix |
# Receiver Input / Output Ports | # 1 x HDMI Female port / 1 x CAT6 |
# 1 x IR Tx / 1 x IR Rx / 1 x Phoenix |
# Power Supply | # DC 24V 1A |
# ESD Protection | # ±?8kV ( air - gap discharge ) |
# Human Body Model : | # ± 4kV ( contact discharge ) |
# Dimensions ( mm ) | # 65 ( W ) X 115 ( D ) X 17 ( H ) |
# Weight | # 200g x 2 |
# Operating Temperature | # 0°C ~ 40°C / 32°F ~ 104°F |
# Storage Temperature | # - 20°C ~ 60°C / - 4°F ~ 140°F |
# Relative Humidity | # 20 ~ 90 % RH ( Non - condensing ) |
# Power Consumption ( Max ) | # 20W |
- - - -
?
Operation controls and Functions
Transmitter
?
?
1 . POWER : This LED illuminates when the device is connected with power supply .
2 . DC 24V : Plug the 24V DC power supply into the unit .
3 . HD BaseT OUT : Standard HD BaseT signal output port . Connect HD BaseT receiver with a UTP cable following the standard of TIA / EIA - 568 - B .
4 . HDMI IN : HDMI input port. This slot is where you connect the HDMI source .
5 . IR IN : Channel 2 IR Receiver . Connect with Wideband IR Rx .
? ? ? ?6 . IR OUT : Channel 1 IR Transmitter. Connect with Wideband IR Tx .
? ? ? ?7 .?RS232 : Phoenix jack provide Serial port control signal from receiver or to receiver .
8 . Connection Signal Indicator Lamp
# Illuminate : The Transmitter and Receiver are in good connections status .
# Flashing : The Transmitter and Receiver are in poor connections status .
# Dark : The Transmitter and Receiver are not connected .
? ? ? ?9 . Data Signal Indicator Lamp
# Illuminate : The HDMI signal with HDCP.
# Flashing : The HDMI signal without HDCP.
# Dark : No HDMI signal.
?
Receiver
?
?
1 . POWER : This LED illuminates when the device is connected with power supply .
2 . DC 24V : Plug the 24V DC power supply into the unit .
? ? ? ?3 . IR IN : Channel 1 IR Receiver . Connect with Wideband IR Rx .
4 . IR OUT : Channel 2 IR Transmitter . Connect with Wideband IR Tx .
5 . HDMI OUT : HDMI output port . This slot is where you connect the HDTV or monitor with HDMI cable .
6 . HD BaseT IN : Standard HD BaseT signal input port . Connect HD BaseT transmitter with a UTP cable following the standard of IEEE - 568B .
? ? ? ?7 . RS232 : Phoenix jack provide Serial port control signal from receiver or to receiver .
8 . Connection Signal Indicator Lamp :
# ?Illuminate : The Transmitter and Receiver are in good connection status .
# ?Flashing : The Transmitter and Receiver are in poor connection status .
# ?Dark : The Transmitter and Receiver are not connected .
Description 1
?
POE ( Power Over Ethernet ) Application Example
?
?
Description 2
?
Bidirectional Infrared control Application Example
?
?
?
Description 3
?
Bidirectional RS232 control Application Example
?
?
?
?
Application Example?
?
Package Contents
?
- - - -
# HDMI Extender Transmitter | # 1PCS |
# HDMI Extender Receiver | # 1PCS |
# Wideband IR Tx | # 2PCS |
# Wideband IR Rx | # 2PCS |
# 24V1A DC Power Supply | # 1PCS |
# Operation Manual | # 1PCS |
# Mounting ears | # 4PCS |
- - - -
?
?
?
Read More
SZ DODONET TECHNOLOGY CO.,LTD
VGA Video Converter,HDMI Switch Box,HDMI Signal Splitter
Address: 3rd floor ,Xinbaoyi electronic park ,Houting the third tech park ,Shajing town,Bao'an district ,Shenzhen ,China,
Shenzhen, Guangdong
China, 518000
Tel: 86-137-14429421
Fax: 86-137-14429421
